Innlegg: 425
Tråder: 28
Ble medlem: Aug 2007
Omdømme:
0
Fikk feil på bremsene på eu-kontrollen. pulserene bremser. dvs hjulene låser ikke.
Har byttet servo-pumpa da denne lakk.
så spørsmålet er, kan det forsatt være luft i bremseveska? alt av hjulsylindere og kaliptere er byttet. eller kan det være hydro-buster som kødder?
Innlegg: 486
Tråder: 31
Ble medlem: Jul 2010
Omdømme:
0
<!--quoteo(post=1620602:date=10 May 2011, 16:29:name=eriknor)-->QUOTE(eriknor @ 10 May 2011, 16:29) <{POST_SNAPBACK}><!--quotec-->Fikk feil på bremsene på eu-kontrollen. pulserene bremser. dvs hjulene låser ikke.
Har byttet servo-pumpa da denne lakk.
så spørsmålet er, kan det forsatt være luft i bremseveska? alt av hjulsylindere og kaliptere er byttet. eller kan det være hydro-buster som kødder?<!--QuoteEnd--><!--QuoteEEnd-->
hvis det var bak så skal bremsene der slippe opp hvis hjulene slipper, for så og komme på igjen, og regner med at du har abs på bilen
kanskje litt greit og vite hva type bil du har, om den er reg som personbil eller lastebil/combi, årsmod,
Innlegg: 425
Tråder: 28
Ble medlem: Aug 2007
Omdømme:
0
<!--quoteo(post=1620603:date=10 May 2011, 16:38:name=andre5)-->QUOTE(andre5 @ 10 May 2011, 16:38) <{POST_SNAPBACK}><!--quotec-->hvis det var bak så skal bremsene der slippe opp hvis hjulene slipper, for så og komme på igjen, og regner med at du har abs på bilen
kanskje litt greit og vite hva type bil du har, om den er reg som personbil eller lastebil/combi, årsmod,<!--QuoteEnd--><!--QuoteEEnd-->
er en 88 model suburban, ikke abs. står hverken bak eller fremme, bare pulserene bremser.
bytter uansett hydroen, den lekker litt.
Innlegg: 4,559
Tråder: 94
Ble medlem: Sep 2007
Omdømme:
0
kan jo være den RWAL som kødder for deg å da
tror du skal ha den på din selv om du ikke har abs.
står så i chilton boka mi for chevy truck 88-98
Svein
LA3CLA
-------------------------------------------------------------------------------------------
98mod 6,5TD Chevrolet Suburban K1500LS 4wd 8bolter. m/detroit true track diffrensial
DS4-5521 IP m/#9 motstand pluss cooler, operation dieselflow, fleetguard spin-on dieselfilter, Icom Ic-7000 HF/VHF/UHF radio, Icom ic-AH4 Antennetuner og 1,65m kort Springer antenne hvor antenne foten er modifisert til Longwire type, 5/8 ECO antenne på VHF
Innlegg: 425
Tråder: 28
Ble medlem: Aug 2007
Omdømme:
0
<!--quoteo(post=1620613:date=10 May 2011, 18:25:name=KapteinMike)-->QUOTE(KapteinMike @ 10 May 2011, 18:25) <{POST_SNAPBACK}><!--quotec-->kan jo være den RWAL som kødder for deg å da
tror du skal ha den på din selv om du ikke har abs.
står så i chilton boka mi for chevy truck 88-98<!--QuoteEnd--><!--QuoteEEnd-->
Rwal? du tenker da på posjonerings ventilen?
Innlegg: 4,559
Tråder: 94
Ble medlem: Sep 2007
Omdømme:
0
RWAL = Rear wheel anti-lock
satt det på mye USA bil på 80-90tall før ABS gjorde inntog
Svein
LA3CLA
-------------------------------------------------------------------------------------------
98mod 6,5TD Chevrolet Suburban K1500LS 4wd 8bolter. m/detroit true track diffrensial
DS4-5521 IP m/#9 motstand pluss cooler, operation dieselflow, fleetguard spin-on dieselfilter, Icom Ic-7000 HF/VHF/UHF radio, Icom ic-AH4 Antennetuner og 1,65m kort Springer antenne hvor antenne foten er modifisert til Longwire type, 5/8 ECO antenne på VHF
Innlegg: 425
Tråder: 28
Ble medlem: Aug 2007
Omdømme:
0
10.05.2011, 20:26
(Dette innlegget blei sist endra: 10.05.2011, 20:41 av eriknor.)
<!--quoteo(post=1620624:date=10 May 2011, 20:51:name=KapteinMike)-->QUOTE(KapteinMike @ 10 May 2011, 20:51) <{POST_SNAPBACK}><!--quotec-->RWAL = Rear wheel anti-lock
satt det på mye USA bil på 80-90tall før ABS gjorde inntog<!--QuoteEnd--><!--QuoteEEnd-->
vet åssen ventil du mener. kan jo være den.
på åssen måte kan denne ventilen kødde det til?
Innlegg: 225
Tråder: 18
Ble medlem: May 2007
Omdømme:
0
Har det samme problemet med bak bremsene... 91 mod burb...
Hva skal en gjøre med dette da? Lufte noe?
Innlegg: 73
Tråder: 0
Ble medlem: Sep 2008
Omdømme:
0
<!--quoteo(post=1620602:date=10 May 2011, 16:29:name=eriknor)-->QUOTE(eriknor @ 10 May 2011, 16:29) <{POST_SNAPBACK}><!--quotec-->Fikk feil på bremsene på eu-kontrollen. pulserene bremser. dvs hjulene låser ikke.
Har byttet servo-pumpa da denne lakk.
så spørsmålet er, kan det forsatt være luft i bremseveska? alt av hjulsylindere og kaliptere er byttet. eller kan det være hydro-buster som kødder?<!--QuoteEnd--><!--QuoteEEnd-->
Kast i bremseskiver/tromler?
Innlegg: 4,559
Tråder: 94
Ble medlem: Sep 2007
Omdømme:
0
<!--quoteo(post=1620627:date=10 May 2011, 21:26:name=eriknor)-->QUOTE(eriknor @ 10 May 2011, 21:26) <{POST_SNAPBACK}><!--quotec-->vet åssen ventil du mener. kan jo være den.
på åssen måte kan denne ventilen kødde det til?<!--QuoteEnd--><!--QuoteEEnd-->
nå spør du egentlig vanskelig men pulserende bremser må jo ha sin opprinnelse
spørs jo helt ann på om det er foran eller bak som skylder dette
RWAL har du isåfal kun på bremsekretsen bak
men pulsering kan jo komme av skiver/trommler eller trege hjulsylindere osv
mulig du kan finne sikringen til RWAL i sikringsboksen. da kan du jo prøve bytte/ta ut for å eliminere/konstantere
Svein
LA3CLA
-------------------------------------------------------------------------------------------
98mod 6,5TD Chevrolet Suburban K1500LS 4wd 8bolter. m/detroit true track diffrensial
DS4-5521 IP m/#9 motstand pluss cooler, operation dieselflow, fleetguard spin-on dieselfilter, Icom Ic-7000 HF/VHF/UHF radio, Icom ic-AH4 Antennetuner og 1,65m kort Springer antenne hvor antenne foten er modifisert til Longwire type, 5/8 ECO antenne på VHF
Innlegg: 225
Tråder: 18
Ble medlem: May 2007
Omdømme:
0
Dette må jeg kikke litt på i den haynes boka mi...
Har nettopp, vel ikke nettopp kanskje, men ikke så lenge siden da, byttet bremse klosser på tromlene bak og det var etter da det begynte.... Merker ikke noe med en gang, men så komemr det og pulseringen blir verre og verre...
Hm......Ta vekk hele dritten muligens? Bremsene bak går vel på senere enn de foran uansett, så hva skal vi med denne RWAL'en?
Innlegg: 425
Tråder: 28
Ble medlem: Aug 2007
Omdømme:
0
hvor sitter denne ventilen som dere snakker om?
Innlegg: 4,559
Tråder: 94
Ble medlem: Sep 2007
Omdømme:
0
<!--quoteo(post=1620663:date=11 May 2011, 14:51:name=eriknor)-->QUOTE(eriknor @ 11 May 2011, 14:51) <{POST_SNAPBACK}><!--quotec-->hvor sitter denne ventilen som dere snakker om?<!--QuoteEnd--><!--QuoteEEnd-->
muligens nær masterbrake sylinder i motorommet kansje..
er ikke helt sikker på hvor sitter... har selv 98sub med ABS hjerne i motorommet
men hvis du har en sikring som går til RWAL ta ut denne først...
Svein
LA3CLA
-------------------------------------------------------------------------------------------
98mod 6,5TD Chevrolet Suburban K1500LS 4wd 8bolter. m/detroit true track diffrensial
DS4-5521 IP m/#9 motstand pluss cooler, operation dieselflow, fleetguard spin-on dieselfilter, Icom Ic-7000 HF/VHF/UHF radio, Icom ic-AH4 Antennetuner og 1,65m kort Springer antenne hvor antenne foten er modifisert til Longwire type, 5/8 ECO antenne på VHF
Innlegg: 4,559
Tråder: 94
Ble medlem: Sep 2007
Omdømme:
0
Kikker litt i noen USA forum mulig dette er noe til hjelp
SAKSET rett ut fra siden:
I have an 88 c1500 4.3l v6 2wd w/ a 5spd standard and RWAL brakes
I have replaced the shoes/pads, new calipers, new wheel cylinders, new springs and self-adjusters, new drums and resurfaced rotors. I've also replaced the master cylinder (Hand bled before installing) and replaced the EBCM (Checked the resistance from pins A-D (4.06 ohms) and pins B-D (1.30 ohms) and cycled the key before plugging in the new one.
I have also cleaned the connections for the parking brake switch and the low level brake switch as well. I also bled the brakes throughly after replacing all these components.
My brakes were still spongy after all this, so I was going to run a diagnostic on the RWAL. However the dash brake light didnt energize so I pulled out the instrument cluster and checked for bad bulbs. I replaced it with a good one, and still no light.
At this point, the only components I haven't replaced are the proportioning valve and the control valve (for the rear brakes).
The parking brake works perfectly, but no brake light comes on when it is engaged.
I disconnected the rear brake line from the master cylinder and plugged it with a plastic fitting. The brakes instantly "pumped up"
here is my dilemma:
1 - in-dash brake light doesn't energize (even with a ground jumpered to the parking brake switch)
2 - the brakes are still spongy when the rear brakes are connected (after bleeding)
any ideas would be very much appreciated.
--------------------------------------------------------------------------------
quaddriver03-21-2004, 12:24 AM
I have an 88 c1500 4.3l v6 2wd w/ a 5spd standard and RWAL brakes
I have replaced the shoes/pads, new calipers, new wheel cylinders, new springs and self-adjusters, new drums and resurfaced rotors. I've also replaced the master cylinder (Hand bled before installing) and replaced the EBCM (Checked the resistance from pins A-D (4.06 ohms) and pins B-D (1.30 ohms) and cycled the key before plugging in the new one.
I have also cleaned the connections for the parking brake switch and the low level brake switch as well. I also bled the brakes throughly after replacing all these components.
My brakes were still spongy after all this, so I was going to run a diagnostic on the RWAL. However the dash brake light didnt energize so I pulled out the instrument cluster and checked for bad bulbs. I replaced it with a good one, and still no light.
At this point, the only components I haven't replaced are the proportioning valve and the control valve (for the rear brakes).
The parking brake works perfectly, but no brake light comes on when it is engaged.
I disconnected the rear brake line from the master cylinder and plugged it with a plastic fitting. The brakes instantly "pumped up"
here is my dilemma:
1 - in-dash brake light doesn't energize (even with a ground jumpered to the parking brake switch)
2 - the brakes are still spongy when the rear brakes are connected (after bleeding)
any ideas would be very much appreciated.
bleed the rwal. common problem, use a scan tool to cycle the pump while bleeding
--------------------------------------------------------------------------------
gen003-21-2004, 02:48 AM
I'm not too sure I'm clear about the process involved in doing that. The Chilton's I have on my truck isn't very clear about it.
On my truck, the rear wheel brake line leaves the master cylinder, goes through the proportioning valve then through the control valve, then out to the wheels. I understand how the ABS works, but I see no wires going to the control valve for the 2 solenoids. Am I missing a component here, or is the pump a seperate component than the control valve I'm speaking of? :confused: The control valve I mentioned is located directly beneath the master cylinder and is mounted to a bracket attached to the power booster (although nothing internal connects to the booster). There is a bleeder valve on the top. I have bled it before, but saw no air whatsoever. Is this what you meant by cycling the pump with a scan tool? :confused:
Also, could I cycle the pump using a jumper wire rather than the tool itself, or is the scanner necessary?
If the scan tool is necessary, will it work if the in-dash brake light doesn't work?
--------------------------------------------------------------------------------
quaddriver03-21-2004, 03:01 AM
I'm not too sure I'm clear about the process involved in doing that. The Chilton's I have on my truck isn't very clear about it.
On my truck, the rear wheel brake line leaves the master cylinder, goes through the proportioning valve then through the control valve, then out to the wheels. I understand how the ABS works, but I see no wires going to the control valve for the 2 solenoids. Am I missing a component here, or is the pump a seperate component than the control valve I'm speaking of? :confused: The control valve I mentioned is located directly beneath the master cylinder and is mounted to a bracket attached to the power booster (although nothing internal connects to the booster). There is a bleeder valve on the top. I have bled it before, but saw no air whatsoever. Is this what you meant by cycling the pump with a scan tool? :confused:
Also, could I cycle the pump using a jumper wire rather than the tool itself, or is the scanner necessary?
If the scan tool is necessary, will it work if the in-dash brake light doesn't work?
yes the solenoids are the 'pumps', what a brake friendly scan tool will do is hold both solenoids open so that the true braking function will be there and it then cycles them to get any bubbles out of the chambers. what I have found with the kelsey hayes rwal/4wal units is that if you change something 'back' towards the wheel cylinders, air bubbles can travel up the line to the unit and wont bleed at the master cyl bleed screws.
--------------------------------------------------------------------------------
gen003-21-2004, 05:10 AM
ok I'll give it a try.
Thanks for the advice [img]style_emoticons/<#EMO_DIR#>/smile.gif[/img]
--------------------------------------------------------------------------------
gen003-21-2004, 07:40 PM
Ok I gave it a shot. I bled the rear wheels first (passenger side then driver side). Then I bled the RWAL valve. They don't sell a scan tool at any of my automotive shops locally, so I couldn't cycle the solenoids in the RWAL. I did however go and drive the truck after bleeding it, and used the brakes really hard to cause the RWAL to kick in to actuate them, and then re-bled it. Still no luck. Spongy as ever.
I still get no in-dash brake light either even with the new EBCM...not even a diagnostic flash at start-up. I rechecked the bulb and even pulled it out and put 12v to it..lit right up.
where could I get a scan tool that can cycle the pumps? All I see locally are OBD II and code readers.
My truck is an OBD I.
Also do you know where I can get an ABS electrical schematic? The chilton's I have doesn't even show the EBCM in the schematics.
--------------------------------------------------------------------------------
quaddriver03-21-2004, 09:08 PM
Ok I gave it a shot. I bled the rear wheels first (passenger side then driver side). Then I bled the RWAL valve. They don't sell a scan tool at any of my automotive shops locally, so I couldn't cycle the solenoids in the RWAL. I did however go and drive the truck after bleeding it, and used the brakes really hard to cause the RWAL to kick in to actuate them, and then re-bled it. Still no luck. Spongy as ever.
I still get no in-dash brake light either even with the new EBCM...not even a diagnostic flash at start-up. I rechecked the bulb and even pulled it out and put 12v to it..lit right up.
where could I get a scan tool that can cycle the pumps? All I see locally are OBD II and code readers.
My truck is an OBD I.
Also do you know where I can get an ABS electrical schematic? The chilton's I have doesn't even show the EBCM in the schematics.
well you needa snap on 2500 or better or modis or the GM star. the KH systems dont publish the internals outside of a dealership...you can get codes and stepguides in a service manual but not wiring.
Schurkey01-13-2010, 02:54 PM
I tried a search, but I can't figure out how to search ONLY the C/K forum. [EDIT: Got it. Separate button from the Search button I'd been using.]
I seem to be losing the vehicle speed sensor signal somewhere AFTER the actual sensor, but prior to the processed signal going to the RWAL, cruise control, speedo, odometer, and ECU.
All of those items will--suddenly and randomly--quit working at the same time. Seems to do it more when temperatures are warm--more in summer than in winter; more after vehicle interior has warmed up in winter. It can and has done it at any time, however. I'll start off in the morning--speedo doesn't work. I'll drive away later--speedo works, get on the highway--speedo and cruise control die. Then they come back 1 to 70 miles later.
Sometimes if I smack the dashboard with my fist, the speedo starts working again.
This produces a Code 9 from the RWAL; and a Code 24 from the ECU. The worst part is that the speedo and the torque converter clutch die also.
The factory service manual diagnostic says to "replace instrument cluster"; but they've been discontinued; used-but-good clusters are somewhat tough to find locally; although I'm prepared to go that route if need be.
1. Who rebuilds the clusters? SOMEBODY has to service these things.
2. WHERE is the ratio adapter plugged into the cluster? The service manual says it's on the back side; but I didn't notice it last time I took that mess apart.
Anyone else having trouble with the electronic speedo and associated VSS-driven items?
--------------------------------------------------------------------------------
777stickman01-13-2010, 07:12 PM
How did you determine that the signal is lost "after" the actual sensor?
In other words how can you be sure it's not the sensor itself or the wiring at the sensor?
Another thing to check is the wiring at the ECU.
--------------------------------------------------------------------------------
Schurkey01-13-2010, 07:49 PM
How did you determine that the signal is lost "after" the actual sensor?
In other words how can you be sure it's not the sensor itself or the wiring at the sensor?
Another thing to check is the wiring at the ECU.
I have AC voltage with the wheels turning (vehicle on jack stands) at the dashboard connector for the instrument cluster. I've had the instrument cluster off the rest of the dashboard three times. The labor isn't terrible, but finding replacement parts is killing me.
The AC signal from the VSS goes to a "buffer" in the instrument cluster; the buffer is affected by a "ratio adapter" which itself is affected by a plug-in chip that calibrates the ratio adapter for tire size and gear ratio. The signal out of the buffer/adapter at 120,000 pulses per mile is fed to the RWAL computer. The 120,000 pulse per mile signal is divided by 32 (to produce 4000 pulses per mile) and fed to the speedo, odometer, and cruise control. Then the 4000 pulse-per-mile signal is divided by 2 (to produce 2000 pulses per mile) and fed to the ECM.
Since the RWAL dies along with everything else downstream, the signal must be corrupted somewhere between the instrument cluster connection and the RWAL (120,000 pulse per mile) output from the buffer/ratio adapter.
I'm hoping there's a bad solder joint (which I have looked for but haven't found) or the ratio adapter chip isn't fully seated. If it isn't something simple like that--I'm screwed; 'cause that's about the limit of my electronics abilities.
Svein
LA3CLA
-------------------------------------------------------------------------------------------
98mod 6,5TD Chevrolet Suburban K1500LS 4wd 8bolter. m/detroit true track diffrensial
DS4-5521 IP m/#9 motstand pluss cooler, operation dieselflow, fleetguard spin-on dieselfilter, Icom Ic-7000 HF/VHF/UHF radio, Icom ic-AH4 Antennetuner og 1,65m kort Springer antenne hvor antenne foten er modifisert til Longwire type, 5/8 ECO antenne på VHF
|